All part numbers in
BOLD MAGENTA
are new this year.
2014 PARTS EUROPE OFFROAD
BRAKES
EXHAUST
TIRES
TUBES &
WHEELS
TIRE
ACCESSORIES
ACCESSORIES
HANDLEBARS
& CONTROLS
FOOT
CONTROLS
BODY
GRAPHICS
& SEATS
SPROCKETS
CHAINS
BRAKES
SUSPENSION
ELECTRICAL
& GAUGES
ENGINE
FUEL/AIR
SYSTEMS
CHEMICALS
& LUBRICANTS
HARDWARE
& TOOLS
TRANSPORT
& TRAILER
RIDER
ACCESSORIES
MERCHANDISING
INDEX
369
FITS MODEL
FRONT BRAKE PAD/
SHOE PART #
TRW PAD/
SHOE TYPE
REAR BRAKE PAD/
SHOE PART #
TRW PAD/
SHOE TYPE
ALFER
MC 80 87-
1722-0572
MCB75
1722-0410
MCB535
MC 125 88-
1722-0442
MCB572
1722-0572
MCB75
250 GR Enduro 88-
1722-0442
MCB572
1722-0572
MCB75
VR 250 Enduro 98-05
1722-0497
MCB648
1721-1101
2
MCB672
MC 250 88-
1722-0442
MCB572
1722-0572
MCB75
300 GR Enduro 88-
1722-0442
MCB572
1722-0572
MCB75
APRILIA
50 Tuareg 87-
1722-0447
MCB578
1722-0572
MCB75
50 Tuareg -86
1722-0572
MCB75
-
-
50 Tuareg Rally 90-
1722-0447
MCB578
1722-0427
MCB552
FITS MODEL
FRONT BRAKE PAD/
SHOE PART #
TRW PAD/
SHOE TYPE
REAR BRAKE PAD/
SHOE PART #
TRW PAD/
SHOE TYPE
APRILIA (CONT)
MX 50 03-
1722-0561
MCB734
1722-0572
MCB75
RX 50 Racing 04-06
1722-0507
MCB664
1722-0427
MCB552
SX 50 06-
1722-0561
MCB734
1722-0410
MCB535
125 Tuareg 89-
1722-0488
MCB629
1720-0161
MCB628
125 Tuareg Rally 86-88
1722-0431
MCB557
-
-
125 Tuareg Rally 89-91
1722-0477
MCB618
1722-0391
MCB519
125 Tuareg Wind 88-89
1722-0448
MCB579
1722-0427
MCB552
125 Tuareg Wind 90-
1722-0488
MCB629
1720-0161
MCB628
ETX 125 99-
1722-0507
MCB664
1720-0161
MCB628
MX 125 Supermoto 04-06
1722-0497
MCB648
1721-1092
2
MCB667
STANDARD BRAKE PADS
•Organic pad compound with ceramic
underlayer for heat retention
•Long service life
•Suitable for use with all brake disc types
•Solid brake performance, even
in wet conditions
BRAKE PAD AND SHOE APPLICATION CHART
2
SI sintered off‑road brake pad.
DISC BRAKE PADS continued on next page.
RSI SINTER OFF-ROAD
RAC BRAKE PADS
•Completely metallic sinter pad without
anti-corrosion paint finish
•High friction rate, excellent
brake performance
•Wears faster than SI pad compound
•Can be used for cross-country racing
NOTE: All brake pad application PART #s shown are STANDARD compound pads unless noted in chart.
NOTE: Some brake pad applications are available in multiple compound types. To see if additional brake pad compound types are available for your application, check your
brake pad PART # in the cross-reference chart provided.
SRQ SINTER-CARBON
RAC BRAKE PADS
•For front brake caliper use ONLY
•No thermal alignment required;
no break-in run requirements
•High friction coefficient and constant
pressure point
•High material stability and low wear
•Good properties, including for endurance
racing use
•Long service life without any
material hardening
SI SINTERED METAL
OFF-ROAD BRAKE PADS
•Completely metallic sinter pad without
anti-corrosion paint finish
•Long service life even when used
in wet conditions
•Good friction rate
•Can be used in many
off-road environments
SH SINTERED
METAL BRAKE PADS
•For rear brake use ONLY
•Completely metallic sinter pad
•Good performance
•Can be used with nearly any brake
disc type
•Should only be used with bikes that were
originally equipped with sintered metal
brake pads
•Friction rate is matched to the SV pad
SV SINTERED
METAL BRAKE PADS
•For front brake use ONLY
•Completely metallic sinter pad
•Good performance
•Can be used with nearly any brake
disc type
•Should only be used with bikes that were
originally equipped with sintered metal
brake pads
•Limited race track use; not heat resistant
above 400°C
BRAKE PAD SHIMS
•Reduce brake pad vibration and noise and protect the caliper piston
•Self-adhesive rubber/fiberglass shims can be trimmed (if necessary) to fit
any caliper/pad combination
•Sold in a package of four
DESCRIPTION
PART #
Brake pad shims (4‑pk.)
1702‑0132
DISC BRAKE PADS
